GATE ME exam:gate PYQs & Answers — Page 64

Questions 631–640 of 1040. Imported answers require independent review unless marked reviewed.

Topic practice 1040 questionsPage 64 of 104

The thickness of a steel plate with material strength coefficient of 210 MPa, has to be reduced from 20 mm to 15 mm in a single pass in a two-high roll mill with a roll radius of 450 mm and rolling velocity of 28 m/min. If the plate has a width of 200 mm and its strain hardening exponent, n is 0.25, the rolling force required for the operation is ______ kN (round off to 2 decimal places).

Note: Average Flow Stress = Material Strength Coefficient × (True Strain)^n/(1+n)

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

A point ‘P’ on a CNC controlled XY- stage is moved to another point ‘Q’ using the coordinate system shown in the figure below and rapid positioning command (G00). A pair of stepping motors with maximum speed of 800 rpm, controlling both the X and Y motion of the stage, are directly coupled to a pair of lead screws, each with a uniform pitch of 0.5 mm. The time needed to position the point ‘P’ to the point ‘Q’ is ______ minutes (round off to 2 decimal places).

Diagram for Mechanical Engineering question 46

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

Two business owners Sheta and Ashok run their business in two different states. Each of them, independent of the other, produces two products A and B, sells them at Rs. 2,000 per kg and Rs. 3,000 per kg, respectively, and uses Linear Programming to determine the optimal quantity of A and B to maximize their respective daily revenue. Their constraints are as follows: i) for each business owner, the production process is such that the daily production of A has to be at least as much B, and the upper limit for production of B is 10 kg per day, and ii) the respective state regulations restrict Sheta’s production of A to less than 20 kg per day, and Ashok’s production of A to less than 15 kg per day. The demand of both A and B in both the states is very high and everything produced is sold.

The absolute value of the difference in daily (optimal) revenue of Sheta and Ashok is ______ thousand Rupees (round off to 2 decimal places).

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

For a single item inventory system, the demand is continuous, which is 1000 per year. The replenishment is instantaneous and backorders (

units) per cycle are allowed as shown in the figure.

Diagram for Mechanical Engineering question 47

As soon as the quantity (

units) ordered from the supplier is received, the backordered quantity is issued to the customers. The ordering cost is Rs. 300 per order. The carrying cost is Rs. 4 per unit per year. The cost of backordering is Rs. 25 per unit per year. Based on the total cost minimization criteria, the maximum inventory reached in the system is ______ (round off to nearest integer).

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

Consider two cases as below.

Case 1: A company buys 1000 pieces per year of a certain part from vendor ‘X’. The changeover time is 2 hours and the price is Rs. 10 per piece. The holding cost rate per part is 10% per year.

Case 2: For the same part, another vendor ‘Y’ offers a design where the changeover time is 6 minutes, with a price of Rs. 5 per piece, and a holding cost rate per part of 100% per year. The order size is 800 pieces per year from ‘X’ and 200 pieces per year from ‘Y’.

Assume the cost of downtime as Rs. 20 per hour. The percentage reduction in the annual cost for Case 2, as compared to Case 1 is ______ (round off to 2 decimal places).

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

Consider a flow through a nozzle, as shown in the figure below. The air flow is steady, incompressible and inviscid. The density of air is 1.23 kg/m

. The pressure difference, (

) is ______ kPa (round off to 2 decimal places).

Diagram for Mechanical Engineering question 48

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

Consider steady, viscous, fully developed flow of a fluid through a circular pipe of internal diameter

. We know that the velocity profile forms a parabola about the pipe centre line, given by:

m/s, where

is a constant. The rate of kinetic energy (in J/s) at the control surface A-B, as shown in the figure, is proportional to

. The value of

is ______.

Diagram for Mechanical Engineering question 49

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

Water (density 100 kg/m

) flows through an inclined pipe of uniform diameter. The velocity, pressure and elevation at section A are

m/s,

kPa and

m, respectively, and those at section B are

m/s,

kPa and

m, respectively. If acceleration due to gravity is 10 m/s

then the head lost due to friction is ______ m (round off to one decimal place).

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

Air discharges steadily through a horizontal nozzle and impinges on a stationary vertical plate as shown in figure.

Diagram for Mechanical Engineering question 50

The inlet and outlet areas of the nozzle are 0.1 m² and 0.02 m², respectively. Take air density as constant and equal to 1.2 kg/m³. If the inlet gauge pressure of air is 0.36 kPa, the gauge pressure at point O on the plate is ______ kPa (round off to two decimal places).

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

The spectral distribution of radiation from a black body at

K has a maximum at wavelength

. The body cools down to temperature

. If the wavelength corresponding to the maximum of the spectral distribution at

is 1.2 times of the original wavelength

, then the temperature

is ______ K (round off to the nearest integer).

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

GATE ME exam:gate PYQs

Question 46

Question 46

Question 47

Question 47

Question 48

Question 48

Question 49

Question 49

Question 50

Question 50