GATE ME topic:manufacturing PYQs & Answers — Page 32

Questions 311–320 of 1040. Imported answers require independent review unless marked reviewed.

Assuming the material considered in each statement is homogeneous, isotropic, linear elastic, and the deformations are in the elastic range, which one or more of the following statement(s) is/are TRUE?

Your answerSelect all correct options. You can choose more than one.

A body subjected to hydrostatic pressure has no shear stress.

If a long solid steel rod is subjected to tensile load, then its volume increases.

Maximum shear stress theory is suitable for failure analysis of brittle materials.

If a portion of a beam has zero shear force, then the corresponding portion of the elastic curve of the beam is always straight.

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

A square plate is supported in four different ways (configurations (P) to (S) as shown in the figure). A couple moment

is applied on the plate. Assume all the members to be rigid and mass-less, and all joints to be frictionless. All support links of the plate are identical.

Diagram for Mechanical Engineering question 26

The square plate can remain in equilibrium in its initial state for which one or more of the following support configurations?

Your answerSelect all correct options. You can choose more than one.

Configuration (P)

Configuration (Q)

Configuration (R)

Configurations (S)

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

Which of the following heat treatment processes is/are used for surface hardening of steels?

Your answerSelect all correct options. You can choose more than one.

Carburizing

Cyaniding

Annealing

Carbonitriding

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

Consider sand cast of a cube of edge length

. A cylindrical riser is placed at the top of the casting. Assume solidification time,

, where

is the volume and

is the total surface area dissipating heat. If the top of the riser is insulated, which of the following radius/radii of riser is/are acceptable?

Your answerSelect all correct options. You can choose more than one.

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

Which of the following additive manufacturing technique(s) can use a wire as a feedstock material?

Your answerSelect all correct options. You can choose more than one.

Stereolithography

Fused deposition modeling

Selective laser sintering

Directed energy deposition processes

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

Which of these processes involve(s) melting in metallic workpieces?

Your answerSelect all correct options. You can choose more than one.

Electrochemical machining

Electric discharge machining

Laser beam machining

Electron beam machining

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

Which of the following methods can improve the fatigue strength of a circular mild steel (MS) shaft?

Your answerSelect all correct options. You can choose more than one.

Enhancing surface finish

Shot peening of the shaft

Increasing relative humidity

Reducing relative humidity

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

The velocity field in a fluid is given to be

. Which of the following statement(s) is/are correct?

Your answerSelect all correct options. You can choose more than one.

The velocity field is one-dimensional.

The flow is incompressible.

The flow is irrotational.

The acceleration experienced by a fluid particle is zero at

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

The figure shows a purely convergent nozzle with a steady, inviscid compressible flow of an ideal gas with constant thermophysical properties operating under choked condition. The exit plane shown in the figure is located in the nozzle. If the inlet pressure (

) is increased while keeping the back pressure (

) unchanged, which of the following statements is/are true?

Diagram for Mechanical Engineering question 30

Your answerSelect all correct options. You can choose more than one.

Mass flow rate through the nozzle will remain unchanged.

Mach number at the exit plane of the nozzle will remain unchanged at unity.

Mass flow rate through the nozzle will increase.

Mach number at the exit plane of the nozzle will become more than unity.

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

A rope with two mass-less platforms at its two ends passes over a fixed pulley as shown in the figure. Discs with narrow slots and having equal weight of 20 N each can be placed on the platforms. The number of discs placed on the left side platform is

and that on the right side platform is

It is found that for

and

, a force

N (refer to part (i) of the figure) is just sufficient to initiate upward motion of the left side platform. If the force

is removed then the minimum value of

(refer to part (ii) of the figure) required to prevent downward motion of the left side platform is ______ (in integer).

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

GATE ME topic:manufacturing PYQs

Question 26

Question 26

Question 27

Question 27

Question 28

Question 28

Question 29

Question 29

Question 30

Question 30