GATE ME topic:mechanical-engineering PYQs & Answers — Page 88

Home
GATE
Mechanical Engineering
Topics
topic:mechanical-engineering

Questions 871–880 of 1040. Imported answers require independent review unless marked reviewed.

Topic practice 1040 questionsPage 88 of 104

The percentage scrap in a sheet metal blanking operation of a continuous strip of sheet metal as shown in the figure is ______ (correct to two decimal places).

Diagram for Mechanical Engineering question 36

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

Given the ordinary differential equation

with

and

, the value of y is ________ (correct to two decimal places).

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

An explicit forward Euler method is used to numerically integrate the differential equation

using a time step of 0.1. With the initial condition

, the value of

computed by this method is __________ (correct to two decimal places).

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

A thin-walled cylindrical can with rigid end caps has a mean radius R = 100 mm and a wall thickness of t = 5 mm. The can is pressurized and an additional tensile stress of 50 MPa is imposed along the axial direction as shown in the figure. Assume that the state of stress in the wall is uniform along its length. If the magnitudes of axial and circumferential components of stress in the can are equal, the pressure (in MPa) inside the can is ________ (correct to two decimal places).

Diagram for Mechanical Engineering question 37

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

F(s) is the Laplace transform of the function

F(1) is ________ (correct to two decimal places).

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

A bar is subjected to a combination of a steady load of 60 kN and a load fluctuating between −10 kN and 90 kN. The corrected endurance limit of the bar is 150 MPa, the yield strength of the material is 480 MPa and the ultimate strength of the material is 600 MPa. The bar cross-section is square with side a. If the factor of safety is 2, the value of a (in mm), according to the modified Goodman’s criterion, is ________ (correct to two decimal places).

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

A simply supported beam of width 100 mm, height 200 mm and length 4 m is carrying a uniformly distributed load of intensity 10 kN/m. The maximum bending stress (in MPa) in the beam is __________ (correct to one decimal place).

Diagram for Mechanical Engineering question 39

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

A force of 100 N is applied to the centre of a circular disc, of mass 10 kg and radius 1 m, resting on a floor as shown in the figure.

If the disc rolls without slipping on the floor, the linear acceleration (in m/s

) of the centre of the disc is ________ (correct to two decimal places).

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

A machine of mass

kg is supported on two mounts, each of stiffness

kN/m. The machine is subjected to an external force (in N)

. Assuming only vertical translation motion, the magnitude of the dynamic force (in N) transmitted from each mount to the ground is _____ (correct to two decimal places).

Diagram for Mechanical Engineering question 40

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

A frictionless circular piston of area

and mass 100 kg sinks into a cylindrical container of the same area filled with water of density 1000 kg/m

as shown in the figure.

The container has a hole of area

at the bottom that is open to the atmosphere. Assuming there is no leakage from the edges of the piston and considering water to be incompressible, the magnitude of the piston velocity (in m/s) at the instant shown is ______ (correct to three decimal places).

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

GATE ME topic:mechanical-engineering PYQs

Question 36

Question 36

Question 37

Question 37

Question 38

Question 38

Question 39

Question 39

Question 40

Question 40