GATE MN topic:mining-engineering PYQs & Answers — Page 49

Home
GATE
Mining Engineering
Topics
topic:mining-engineering

Questions 481–490 of 650. Imported answers require independent review unless marked reviewed.

Topic practice 650 questionsPage 49 of 65

A low-grade deep-seated ore body dipping at 70° has a strike length of 2 km, and width of 100 m. The ore body and wall rocks are weak and fractured. The preferred method of mining is

Your answerChoose one option.

shrinkage stoping

cut-and-fill stoping

block caving

room and pillar stoping

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

If the figures A and B represent contour plots in a terrain, then the correct statement is

Diagram for Mining Engineering question 17

Your answerChoose one option.

Fig. A shows ridge and Fig. B shows valley

Fig. A shows anticline and Fig. B shows syncline

Fig. A shows syncline and Fig. B shows anticline

Fig. A shows valley and Fig. B shows ridge

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

The availability of water in the root zone for plant use is maximum in the case of

Your answerChoose one option.

sand

loam

clay

gravel

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

If the time to failure of a machine component is exponentially distributed, the reliability of the same at Mean Time To Failure (MTTF), (rounded off to three decimal places), is __________.

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

The major and minor principal stresses at a point are 25 MPa and -5 MPa respectively. The maximum shear stress, in MPa at that point is ______.

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

For a function

and

. Ignoring all higher order terms in Taylor series, the value of the function at

(rounded off to two decimal places) is __________.

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

Proximate analysis of a coal sample gives 2.46% moisture, 25.73% volatile matter, and 42.89% ash. The volatile matter of the coal sample, in percentage, on dry ash free (daf) basis (rounded off to two decimal places) is __________.

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

A coarse sand aquifer has porosity 20% and hydraulic conductivity

m/s. If the hydraulic gradient is 0.00423 (m/m), then the average linear velocity of the groundwater in mm/s, (rounded off to three decimal places) is __________.

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

In a slake durability test, mass of the drum with samples before the test and mass of the drum with oven-dried samples after the test are 1.52 kg and 1.48 kg respectively. If the mass of the drum is 1.05 kg, slake durability index in percentage (rounded off to two decimal places) is __________.

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

The ionic concentration of a mine water sample with pH close to 7.0 is given below. The alkalinity of the water expressed as equivalent CaCO

, in mg/l, (rounded off to two decimal places) is __________.

Cations	mg/l	Anions	mg/l
Ca	95.0	HCO	160.0

You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer

GATE MN topic:mining-engineering PYQs

Question 16

Question 17

Question 18

Question 19

Question 20

Question 21

Question 22

Question 23

Question 24

Question 25