Architecture and Planning
GATE AR topic:architecture PYQs
Build your understanding with focused practice from past exam papers.
Questions 371–380 of 730. Imported answers require independent review unless marked reviewed.
Question 47
Open questionARNAT2 marksNeeds review
A 230 mm thick brick wall of 10 m length and 3 m height is built using a Flemish bond. The size of the bricks used is 230 mm x 112.5 mm x 70 mm. Assuming a mortar thickness of 5 mm, the number of bricks required (in integer) is __________.
Log in to check the answer
You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answerQuestion 48
Open questionARNAT2 marksNeeds review
The reflected ceiling plan and section of a reinforced cement concrete roof are shown in the following figure. All the beams are 300 mm wide, 600 mm deep (including 150 mm slab depth) and are placed center to center. Assuming 1% of concrete volume is occupied by reinforcement bars, the volume of concrete (in cubic meters, rounded off to two decimal places) is __________.
Log in to check the answer
You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answerQuestion 49
Open questionARNAT2 marksNeeds review
The following graph represents the income distribution among the population of a country. The Gini Coefficient of the country (rounded off to three decimal places) is __________.
Log in to check the answer
You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answerQuestion 50
Open questionARMCQ1 markNeeds review
Which of the following process is used for surface treatment of metals?
Your answerChoose one option.
Log in to check the answer
You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answerQuestion 51
Open questionARMCQ1 markNeeds review
Among the following monuments of ancient Greece, the only Octastyle Peripteral temple with eight towering Doric columns lining both east and west facades is __________.
Your answerChoose one option.
Log in to check the answer
You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answerQuestion 52
Open questionARMCQ1 markNeeds review
An Ultrasonic Pulse Velocity (UPV) test was done on a hardened concrete element using a direct transmission method as per IS 516 (Part 5/Section 1): 2018. The distance between the transducer and receiver was 600 mm. The time taken for the induced wave to travel this distance is measured as 0.18 milliseconds. Based on the following Table, the concrete quality grading is __________.
Velocity (km/s) – cross probing | Concrete quality grading |
|---|---|
Above 4.4 | Excellent |
3.75 – 4.4 | Good |
3.0 – 3.75 | Doubtful |
Less than 3.0 | Poor |
Your answerChoose one option.
Log in to check the answer
You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answerQuestion 53
Open questionARMSQ1 markNeeds review
Which of the following is/are example(s) of Tomb Architecture of Ancient Egypt?
Your answerSelect all correct options. You can choose more than one.
Log in to check the answer
You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answerQuestion 54
Open questionARMSQ1 markNeeds review
If Aluminium : Anodisation :: Glazing : X, which of the following choices present X?
Your answerSelect all correct options. You can choose more than one.
Log in to check the answer
You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answerQuestion 55
Open questionARNAT1 markNeeds review
A blackbody radiant heating panel of 5 m² surface area at 35 °C surface temperature is located 1 m away from a 1 m² surface at 20 °C. The Stefan-Boltzmann constant is 5.670×10⁻⁸ W m⁻² K⁻⁴. The rate of radiant heat emission by the radiant heating panel (in W, rounded off to two decimal places) is __________.
Log in to check the answer
You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answerQuestion 56
Open questionARNAT1 markNeeds review
A hypothetical truss comprising of weightless members is shown in the following Figure. Assuming tension to be positive and compression to be negative, the value of force in member TU (in kN, rounded off to one decimal place) is __________.
Log in to check the answer
You can attempt this question now. Sign in to view the answer key, explanations and discussion.Log in to check answer